angelshas.blogg.se

Wince copy rom files download
Wince copy rom files download





wince copy rom files download
  1. #WINCE COPY ROM FILES DOWNLOAD SERIAL#
  2. #WINCE COPY ROM FILES DOWNLOAD FULL#
  3. #WINCE COPY ROM FILES DOWNLOAD DOWNLOAD#
  4. #WINCE COPY ROM FILES DOWNLOAD WINDOWS#

In Kernel Service Map, select Ethernet for Download and Transport options and KdStub for the Debugger.Click on Add Device and provide a device name (e.g.In Platform Builder, go to Target > Connectivity Options.Perform the following steps to setup a connection between the EM-X270 evaluation platform and Platform Builder 6.0 : Connect the EB-X270 Ethernet connector (P3) to your local network.Setup Target for EM-X270 Image Evaluation Format user data partition (together with registry hives) before the boot The proper partition layout is created beforehand Start download of NK.bin from Platform Builder and store it in the NAND Flash. Start download of NK.bin from Platform Builder Perform low level format of NAND Flash including bad block erase (take more than 5 min to complete)

wince copy rom files download

Perform low level format of NAND Flash If disabled, the WinCE image is read from the NAND Flash on startup Set auto download of an image from a development station. If you use DHCP you do not need to set IP address and subnet mask Enable/Disable DHCP when downloading an image from a development station. Set the boot delay in range 0 - 255 seconds Set Subnet Mask to use when downloading an image from a development station Set IP Address to use when downloading an image from a development station Launch existing flash resident image nowīrief description of Eboot main menu functionality can be found below: When the boot sequence is interrupted, Eboot enters menu-driven configuration mode. In order to access the Eboot main menu interrupt the automatic boot sequence by pressing any key other than ENTER during the specified timeout interval.

  • Restart the system and enter the Eboot main menu.
  • Hit any key to stop the U-boot auto boot and enter the command prompt.
  • It should print a welcome greeting and some hardware initialization info.
  • Check the reports on the terminal screen.
  • wince copy rom files download

    Check the activity of the green LED (DS1) on the EM-X270 - it should light up and then start blinking

    #WINCE COPY ROM FILES DOWNLOAD SERIAL#

  • Ensure that you have a serial terminal connected to the EM-X270 evaluation platform as described in Console setup.
  • On power up, U-boot initializes hardware and transfers control to Eboot, which automatically loads the WinCE image from NAND Flash after the predefined time out interval (1s). It can be used to establish a connection with Platform Builder for further debugging or image download. In fact, it is recommended to permanently remove these two commands from the build menu.ĭuring the LiveDisk installation Eboot (Microsoft WinCE bootloader) is stored into the NOR Flash.
  • Use Build->Advanced Build Commands-> Build Current BSP and Subprojects when you add/remove CompuLab BSP Platform Builder components to/from the project or perform changes in BSP files.ĭo not use Build->Advanced Build Commands->Build and Sysgen or Build->Advanced Build Commands->Rebuild and Clean Sysgen commands that compile and perform sysgen on the entire Platform Builder tree.
  • Use Build->Advanced Build Commands->Sysgen when you add/remove Platform Builder components (Catalog items) to/from the project.
  • The build process takes about 15-20 minutes. Perform "Rebuild Solution" from the "Build" menu (alternatively you can perform "Build-Advanced Build Commands->Clean Sysgen").

    #WINCE COPY ROM FILES DOWNLOAD FULL#

    Make sure that the project is configured for Release mode (the full debug image is very large and it is not recommended to build it). The Platform Project and the workspace will be opened. In order to build the EM-X270 platform, select the "Open >Project/Solution" command from the File menu of the VS2005 and select the

    #WINCE COPY ROM FILES DOWNLOAD WINDOWS#

    A custom Windows CE image built for a specific application is typically much smaller and in most cases does not exceed 5-10MB. The demo image size is relatively large, ~40 MB. It includes many components and is highly recommended as a starting point. The EM-X270 Platform Project is used to build CompuLab’s WinCE demo image. Copy the EM_X270_CE6 directory into \WINCE600\OSDesigns.Copy the EM_X270_BSP directory into \WINCE600\Platform.Close the Platform Builder Application.5.2 Advanced BSP customization using batch files.5.1 Managing BSP components with Platform Builder Catalog.4.2 Download image from Platform Builder.4.1 Setup Connection with Platform Builder.4 Setup Target for EM-X270 Image Evaluation.







    Wince copy rom files download